Safety Relief Valve

Product Details:

4Matic Pilot-operated pressure relief valve

 Pressure relief valves (PRV), pilot-operated relief valves (PORV) are used for emergency relief during overpressure events (e.g., a tank gets too hot and the expanding fluid increases the pressure to dangerous levels). PORV are also called pilot-operated safety valve (POSV), pilot-operated pressure relief valve (POPRV), or pilot-operated safety relief valve (POSRV), depending on the manufacturer and the application. Technically POPRV is the most generic term, but PORV is often used generically even though it should refer to valves in liquid service.
In conventional PRVs, the valve is normally held closed by a spring or similar mechanism that presses a disk or piston on a seat, which is forced open if the pressure is greater than the mechanical value of the spring. In the PORV, the valve is held shut by piping a small amount of the fluid to the rear of the sealing disk, with the pressure balanced on either side. A separate actuator on the piping releases pressure in the line if it crosses a threshold. This releases the pressure on the back of the seal, causing the valve to open.
The essential parts of a PORV are a pilot valve (or control pilot), a main valve, a pilot tube, the dome, a disc or piston, and a seat. The volume above the piston is called the dome.
Mode of functioning
The pressure is supplied from the upstream side (the system being protected) to the dome often by a small pilot tube. The downstream side is the pipe or open air where the PORV directs its exhaust. The outlet pipe is typically larger than the inlet. 2 in × 3 in (51 mm × 76 mm), 3 in × 4 in (76 mm × 102 mm), 4 in × 6 in (100 mm × 150 mm), 6 in × 8 in (150 mm × 200 mm), 8 in × 10 in (200 mm × 250 mm) are some common sizes.
The upstream pressure tries to push the piston open but it is opposed by that same pressure because the pressure is routed around to the dome above the piston. The area of the piston on which fluid force is acting is larger in the dome than it is on the upstream side; the result is a larger force on the dome side than the upstream side. This produces a net sealing force.

The pressure from the pilot tube to the dome is routed through the actual control pilot valve. There are many designs but the control pilot is essentially a conventional PRV with the special job of controlling pressure to the main valve dome. The pressure at which the control pilot relieves is the functional set pressure of the PORV. When the pilot valve reaches set pressure it opens and releases the pressure from the dome. The piston is then free to open and the main valve exhausts the system fluid. The control pilot opens either to the main valve exhaust pipe or to atmosphere.

Country to serve:Kyrgyzstan, Nepal, Bhutan, Laos, Myanmar, Thailand, Vietnam, Spratley, Brunei, Malaysia, Combodia, Singapore, Indonesia, Est Timor, Australia, Niue, Samoa, Wallis and futuna, Fiji, New Caledonia, Samoa, Tokelau, Kiribati, Tuvalu, Solomon, Nauru, Papua New Gunea, Micronesia, Palau, Micronesia, Guam, Marshall, Northern Maniana, Philippines, Taiwan, South Korea, North Korea, Japan, Sri Lanka, Maldives, Afghanistan, Uzbekistan, Tajikistan, Kazakhstan, Mongolia, Russia.
Indonesia, Malaysia, South Africa, Ghana, Nigeria, Senegal, Egypt, Turkey, Benin, Burkina Faso, Cape Verde, Cote d''''Ivoire (Ivory Coast), Gambiav, Guinea, Guinea-Bissau, Liberia, Mali, Mauritania, Niger, Saint Helena, Sierra Leone, Sao Tome and Principe Togo, Algeria, Libya, Morocco, Tunisia, South Sudan, Sudan, Western Sahara (Territory), Jordan, Bahrain, Iraq, Iran, Qatar, Kuwait, Syria, Israel, Cyprus, Lebanon, Canada.
Waste water treatment, Municipal water supplier, Oil exploration, Dig and mining, Chemical industries, Sugar industries, Fertilizer Manufacturer, Shipbuilding manufacturer.

Additional Information:

• Item Code: Standard
• Production Capacity: 21000
• Delivery Time: Standard
• Packaging Details: Standard

Product Details:

The primary function of a safety valve is to protect property and life.
Because a safety valve is often the last device to prevent catastrophic failure under pressure conditions, it is important that the valve works at all times i.e. it must be 100% reliable.
Safety valves should be installed wherever the maximum allowable working pressure of a system or pressure containing vessel is likely to be exceeded, in particular under fault conditions due to the failure of another piece of equipment in the system.
Pressure excess can be generated in a number of different ways including:

• Failure of a cooling system allowing vapour or fluid to expand
• Compressed air or electrical power failure to control instrumentation
• Plant fires
• During the start-up conditions of a plant

Additional Information:

• Production Capacity: 20

Product Details:

The Breather Valve is a protection device mounted on a nozzle opening on the top of a fixed roof atmospheric storage tank. Its primary purpose is to protect the tank against rupturing or imploding.

Additional Information:

• Production Capacity: 30